隆客色??！

TEL:

產品名稱：灑精測試儀

型號：AT6000

AT6000呼出氣體酒精含量探測器是專用于測試人體呼出氣體中酒精含量的儀器。本機敏感元件采用漢威電子先進的納米半導體酒精傳感器，具有極好的靈敏度和出色的重復性；測試程序由人工智能設計的微電腦控制，工作流程合理，簡潔便利，功能齊全，具有多種自適應能力；背光照明的LCD數碼、字圖顯示，直觀清晰；小巧的便攜設計更便于您移動使用。當被測呼出氣體中的酒精含量超過預定值時，本機會自動發出聲音報警，為您的安全多一份提醒。

【產品主要技術參數】

【型   號】AT6000

【傳感器類型】 納米半導體酒精傳感器

【工作電壓】 DC4.5V（3×AAA電池）

【欠壓指示】 Vcc＜3.30V±0.10V顯示欠壓；Vcc＜3.00V±0.10V欠壓關機

【工作電流】 ≤120mA

【使用環境】 溫度： -10℃～50℃      相對濕度：≤95%   無結露

【測試響應時間】 ＜5s

【預熱時間】 ＜20s

【測量范圍】 (0.00～1.00)mg/L(0.00～0.20%BAC；0.00～2.00mg/L)

【報警濃度】 0.24mg/L(0.05%BAC； 0.50g/L)

【精 確 度】 ±10% F.S

【報警方式】 聲報警

【顯示方式】 帶藍色背光的3位 LCD 數字配合圖文顯示

【重    量】 ≤64g  (不含電池)

【外形尺寸】 l×b×h，mm ：103×65×27

【顏    色】 黑色

使用說明：
按屏幕正面長按1-3秒“POWER”開機鍵進入約10秒的傳感器預熱倒計時過程。

當看到屏幕出現BIOW字樣開始吹氣 (向吹氣孔連續吹氣約3-6秒鐘左右 進入約5秒的反應期同時測試結果會顯示在LCD上，約5秒鐘后自動關機。

將口部貼近呼氣測試感應器，并連續3-6秒呼氣到感應器內。

顯示屏可讀取測試結果。

當測試結果達到下列范圍時，“Caution”“警告”字句便會顯示
   √0.02% BAC(or 0.2g/l)to 0.05%
BAC(or 0.5g/l)
     0.05% BAC(or 0.5g/l)to 0.08% BAC(or 0.8g/l)

當測試結果達到下列的范圍，“Danger""危險"字句便會顯示。
   √over & EQUAL 0.05% BAC (or
0.5g/l)
     over & EQUAL 0.08% BAC (or 0.8g/l)

《機動車駕駛員駕車時血液中酒精含量規定》強制性全國標準:規定血液中酒精含量大于或等于0.2mg/ml時駕駛機動車為酒后駕車；大于或等于0.8mg/ml時駕駛機動車為醉酒駕車。

報警聲音說明:
當測試結果比預設的報警點低,其差值大于0.2‰BAC時,數字顯示測試結果,無報警聲.
當測試結果比預設的報警點低,其差值小于或等于0.2‰BAC時,數字顯示測試結果,有預報警聲.(只有當報警點大于0.20‰BAC心上時才有此項功能.)

維護與保養
請勿使用苯、稀釋劑或汽油等溶劑清潔本產品，以免損壞機體外殼。
防止跌落和強震，否則會導致本機故障。
除更換電池外，請勿嘗試修理、改造或拆卸零件。
如果長時間不使用本產品時，請取出電池，以免因電池漏液而損壞本機。

本產品設計、制造、檢驗遵守以下國家標準：
GB/T21254-2007《呼出氣體酒精含量檢測儀》
GB19522-2004《車輛駕駛?cè)藛T血液、呼氣酒精含量閾值與檢驗》

特點:
◆ 先進的納米半導體酒精傳感器；
◆ 響應、恢復迅速、檢測快捷方便；
◆ SMD裝配工藝，性能穩定可靠；
◆
人工智能微電腦控制；
◆ 測試過程屏幕直觀顯示；
◆ 藍色背光照明的LCD數碼、字圖顯示；
◆ 便攜設計、小巧輕便；
◆
酒精超限自動聲報警；
◆ 傳感器故障自檢；
◆ 智能節電設計，電池欠壓指示

產品使用

1   打開本機后殼的電池蓋，將3節AAA、1.5V的電池按極性裝入本機，然后再裝上電池蓋，即可投入使。
2  
按下“開機”鍵，伴隨一短促蜂鳴聲，背光點亮，同時屏幕顯示從100到000的倒計時，屏幕下部顯示“WAIT”字樣,提示機器運行預熱程序，此時請不要吹氣，否則會影響測試。預熱完畢，“WAIT”顯示消失，探測器發出一聲蜂鳴，同時顯示“BLOW”字樣，“C”字母游動顯示，此時即可開始下一步的呼出氣體酒精含量測試。

說明：預熱過程中，倒計時速度與上次測試濃度有關，濃度越低，倒計時越快，否則越慢。

3   被測試者深吸氣，當屏幕上“C”字母游動顯示時對準本機吹嘴連續均勻吹氣，直到本機發出一聲蜂鳴，停止吹氣。

4  
吹氣結束，屏幕游動顯示“”符號，同時顯示“TEST”字樣，提示正在分析測試結果，此時不要吹氣，否則會影響測試結果。分析結束后屏幕上所顯示的濃度值即為測試者呼出氣體中的酒精含量，該值保持?jǐn)?shù)秒之后，本機自動關機。

5   若要進行下測試，須重新按“開機”鍵，過程參照上述2～4。

使用說明

1、按動開關健，測試儀的LCD顯示屏便會亮燈，同時會發出“咇”的一聲。
2、數字亦會由10跳到0，便完成預熱程序。
3、將口部貼近呼氣測試感應器，并連續3-5秒呼氣到感應器內。
4、顯示屏可讀取測試結果。
5、當測試結果達到下列范圍時，“Caution”“警告”字句便會顯示
  
√0.02% BAC(or 0.2g/l)to 0.05% BAC(or 0.5g/l)
     0.05% BAC(or 0.5g/l)to
0.08% BAC(or 0.8g/l)
6、當測試結果達到下列的范圍，“Danger""危險"字句便會顯示。
   √over &
EQUAL 0.05% BAC (or 0.5g/l)
     over & EQUAL 0.08% BAC (or
0.8g/l)
7、《機動車駕駛員駕車時血液中酒精含量規定》強制性全國標準:規定血液中酒精含量大于或等于0.2mg/ml時駕駛機動車為酒后駕車；大于或等于0.8mg/ml時駕駛機動車為醉酒駕車。

--------------------------------------------------------------------------------
[溫馨提示]
·喝酒后，建議先稍待20分鐘再檢測，因為酒精需要約20分鐘的時間從消化器官進入血液內，
 
而殘留在口腔的酒精也需要時間消散。
·要得到更準確的結果，每次測試之間應距離少三分鐘時間。
·請勿使用含苯，汽油及天拿水成份的產品清潔測試儀。
·請勿讓任何液體滲進感應器內。
·夢王汽車用品專營店提醒您，為了您和他人的安全，請勿酒后駕車。

【產品圖片展示】

Preface

Reminding Before your testing.

Alco Smart Breath tester should be used only to give an indication of the possible presence of alcohol in the breath/blood. You should not rely upon it as the sole basis to determine intoxication or whether it is safe to drive a vehicle, operate equipment, or engage in dangerous activities.

Everyone has different body responds to alcohol consumption and his testing result only as reference, not a subject standard for consequent decision.

The manufacture, importer or distributor takes no responsibility whatsoever for the use ofthis product for any reason. This product must not be used as a tool for determining whether a person is able to operate a motor vehicle or device legally or safely. The intake of any alcohol will impair reflexes and judgment to operate motor vehicle.

Before your testing, please view the manual carefully and follow the instruction strictly.

General Introduction

AT6000breath alcohol tester is kind of tester designed to measure concentration result of the breathed alcohol in the human body.This device adopts advanced flat surfaced alcohol sensor which has excellent sensitivity andreproducibility, fashional and portable design make it more convenient for personal use. When the alcohol content exceeds the preset limited level, this device would send an audio and videowarning to remind your safety.

Main Feature:

Advanced flat surfaced alcohol sensor

Quick response

SMD assembling, stable performance

Smart MCU control

Direct testing process LCD indication

Digital LCD display with light blue backup

Portable and fashion design?

Audio warning beyond pre-set limit

Sensor fault self checking?

Batterysaved design, low voltage indication

Technical Data

Sensor type: Flat surfaced alcohol sensor

Detection Range: 0.00 – 0.20BAC%; 0.00～2.00g/L；

0.00 – 2.00BAC‰；0.00 -1.00 mg/L; 0.00 – 200mg/100mL

Alarming Level: 0.05BAC%; 0.50g/L; 0.50 BAC‰; 0.25mg/L; 50mg/100mL

Accuracy: ±10% F.S

Working Voltage: DC4.5V（3×AAA）Batteries; Working Current: ≤120mA

Working Environment: Temperature -10℃～50℃

Relative Humidity ≤95% No Dews

Display: 3 digits LCD display with light blue backup

Dimension: 103×65×27mm (L×W×H), ≤64 g Battery excluded

Batteryexpectancy time: ≥200Times

Digital Indication:

2. Operation Instruction

2.1. Slide down the battery compartment on the back side, insert 3pcs AAA 1.5V batteries inside according to battery polarity indication and close it.

2.2. Press the switch button and last for 1s, the tester would be power on with a buzzer brief ringing, ‘Wait’ shows on down side of screen, meantime it shows 100 to 000 countdown, please wait now, otherwise its accuracy will be not good.

Until “Wait” disappears, tester will send out a ring,meantime shows “BLOW” and “C” gliding, now the test could begin.

Remarks: Its countdown speed will depend on concentration of last test, if concentration is high, it will be slow. If concentration is low, the countdown will be very quick.

2.3. Have a deep breath before testing, and blow directly to gas entry when “C”circularly shows, stop blow when heard its buzzer ring.

2.4. After blowing finished, the LCD screen willshow “ ” circularly, meantime shows “TEST”, this means the tester is analyzing the result, do not blow at this time. After analyze the screen will show the testing results.

It will turn off automatically after keep results for several seconds.

2.5. If a new testing needed, press the switch button again and repeat the above step 4.2～4.4.

3. Notification

3.1. Avoid any fall or strong shock.

3.2. If noise gas with high concentration existed,may the tester won’t work normally.

3.3. If testing is done under low voltage, certain error will be existed between the real value.

3.4. To ensure the testing result, please wait 15 mins to take the testing after your drinking.

3.5. The result may be unreliable for your first test if long time storage, please try second time.

3.6. Do not keep the tester in the environment of corrosive gas (Chlorine etc) for use or deposit, also in other bad surroundings.

3.7. Do not blow smoke to tester directly, especially the smokers.

3.8. When in consecutive testing, if blow immediately after drink, this concentration is very high, there will be some rudimental in mouthpiece. Please wait for at least 1 min to take second test, or, blow clean air for 3 seconds to clean out its mouthpiece.

3.9. After Long time use, there may be dirt on the tester, please use clean cloth to wipe off. Do not use any hard object or the solvent with any Corrosive ingredient.

Remarks: Common Fault and Solving solutions