NDJ-1旋轉粘度計的詳細信息
NDJ-1 Rotational Viscometer Instruction Manual
產品應用：Application
本產品廣泛應用于測定油脂，油漆，塑料，食品，藥物，膠粘劑，化妝品等各種流體的粘性阻力與液體的粘度。在使用時必須按照說明書的要求進行安裝和測量工作。
NDJ-1 Rotational Viscometer is a novel instrument to be used in measuring the viscous resistance and the absolute viscosity of fluid.It is widely applicable to determine the viscosity of various kinds of fluids, such as grease, paint, plastics, food products, pharmaceuticals, bonding agent, etc.
1.主要技術規格：
測量范圍：10~ 105 map.s
轉速： 6,12,30,60 Spin/minute
測量誤差：±5%（牛頓液體）
電源： 220V±10V，50Hz
Main Technical Specification：
Range：Medium Viscosity 10-100,000mPa.s
Low Viscosity 0.1-100mPa.s
Medium Viscosity 4 Rotors of No.s 1,2,3 and 4.
Low Viscosity 1 Rotor of No.0
Speed of Rotor:6rpm,12rpm,30rpm and 60rpm.
Measurement tolerance: ±5%(Newtonian fluid)
Power Supply:220V±10%V.50Hz
2.安裝：
1) 從包裝箱中取出機箱底座與支柱。
2) 將三只水平調整腳旋入底座螺絲孔中（圖一）
3) 主機安裝：
a. 旋松機箱中螺釘取出主機。
b. 旋松手柄固定鈕，將電源線嵌入手柄夾頭槽內
（圖二1）。c. 將手柄穿入夾頭槽底圓孔中（圖二2）
d. 旋緊手柄固定鈕夾緊手柄，并使主機基本保持水平（圖二3）e. 拆除指針主桿上的橡皮圈和主機下端的黃色包裝套圈（圖三）。
警告！在未拆除上述兩項前不可通電開機，否則將損壞機器。
f. 接上電源，調整水平調整腳(圖四），使水準器中水平泡居于中心圓圈中（圖五）。
Installation:
1) Take out the support stand, column from the packing box.
2) Screw the column into the hole at the rear of the support stand with the teethed side facing the front of the support stand. Tighten the 3 adjustments underneath the stand support.
3) Installation of Main Body:
a. Take out of the main body and loose the screw.
b. Loose the fixed button and embed the power cord into the groove of the clamp.
c. Let the handle get through the hole of groove of the clamp.
d. Tighten the fixing screw on lever and keep the main body horizontal.
e. Remove the rubber band on the indicator control lever, release the yellow screw at the lower end of the instrument and lastly remove the yellow packing ring.
Warning！
Do not power on before the 2 operations above, otherwise damage will be caused.
f. Power on, make adjustment of the support stand and make sure the leveling bubble is in the center.
3. 操作：
1) 首先將保護架右旋上儀器下端。
2) 準備被測液體，選擇直徑>or=70mm 的圓柱型容器。
3) 按測量要求的，準確控制被測液體的溫度
4) 估計被測液體黏度值的大致范圍參考量程表選好轉子號，并將轉子左旋入連接螺桿(圖4).然后旋轉升降鈕（圖5），使儀器慢慢地下降，逐漸浸入測量液體中，直至轉子液面標志和液面平為止。（圖4）按下指針鎖定桿，開啟電源開關，放開指針鎖定桿，使轉子在液體中旋轉，一般20~30秒的運轉，待指針趨于穩定。按下指針鎖定桿，使讀數固定下來，再關閉電機，使指針停在讀數窗范圍內，直接讀出數據。當電機關停后，如指針不處于讀書窗內，應繼續按住指針鎖定桿，反復開啟和關閉電機，使指針處于讀數窗內。
NDJ-1 Rotational Viscometer Instruction Manual
產品應用：Application
本產品廣泛應用于測定油脂，油漆，塑料，食品，藥物，膠粘劑，化妝品等各種流體的粘性阻力與液體的粘度。在使用時必須按照說明書的要求進行安裝和測量工作。
NDJ-1 Rotational Viscometer is a novel instrument to be used in measuring the viscous resistance and the absolute viscosity of fluid.It is widely applicable to determine the viscosity of various kinds of fluids, such as grease, paint, plastics, food products, pharmaceuticals, bonding agent, etc.
1.主要技術規格：
測量范圍：10~ 105 map.s
轉速： 6,12,30,60 Spin/minute
測量誤差：±5%（牛頓液體）
電源： 220V±10V，50Hz
Main Technical Specification：
Range：Medium Viscosity 10-100,000mPa.s
Low Viscosity 0.1-100mPa.s
Medium Viscosity 4 Rotors of No.s 1,2,3 and 4.
Low Viscosity 1 Rotor of No.0
Speed of Rotor:6rpm,12rpm,30rpm and 60rpm.
Measurement tolerance: ±5%(Newtonian fluid)
Power Supply:220V±10%V.50Hz
2.安裝：
1) 從包裝箱中取出機箱底座與支柱。
2) 將三只水平調整腳旋入底座螺絲孔中（圖一）
3) 主機安裝：
a. 旋松機箱中螺釘取出主機。
b. 旋松手柄固定鈕，將電源線嵌入手柄夾頭槽內
（圖二1）。c. 將手柄穿入夾頭槽底圓孔中（圖二2）
d. 旋緊手柄固定鈕夾緊手柄，并使主機基本保持水平（圖二3）e. 拆除指針主桿上的橡皮圈和主機下端的黃色包裝套圈（圖三）。
警告！在未拆除上述兩項前不可通電開機，否則將損壞機器。
f. 接上電源，調整水平調整腳(圖四），使水準器中水平泡居于中心圓圈中（圖五）。
Installation:
1) Take out the support stand, column from the packing box.
2) Screw the column into the hole at the rear of the support stand with the teethed side facing the front of the support stand. Tighten the 3 adjustments underneath the stand support.
3) Installation of Main Body:
a. Take out of the main body and loose the screw.
b. Loose the fixed button and embed the power cord into the groove of the clamp.
c. Let the handle get through the hole of groove of the clamp.
d. Tighten the fixing screw on lever and keep the main body horizontal.
e. Remove the rubber band on the indicator control lever, release the yellow screw at the lower end of the instrument and lastly remove the yellow packing ring.
Warning！
Do not power on before the 2 operations above, otherwise damage will be caused.
f. Power on, make adjustment of the support stand and make sure the leveling bubble is in the center.
3. 操作：
1) 首先將保護架右旋上儀器下端。
2) 準備被測液體，選擇直徑>or=70mm 的圓柱型容器。
3) 按測量要求的，準確控制被測液體的溫度
4) 估計被測液體黏度值的大致范圍參考量程表選好轉子號，并將轉子左旋入連接螺桿(圖4).然后旋轉升降鈕（圖5），使儀器慢慢地下降，逐漸浸入測量液體中，直至轉子液面標志和液面平為止。（圖4）按下指針鎖定桿，開啟電源開關，放開指針鎖定桿，使轉子在液體中旋轉，一般20~30秒的運轉，待指針趨于穩定。按下指針鎖定桿，使讀數固定下來，再關閉電機，使指針停在讀數窗范圍內，直接讀出數據。當電機關停后，如指針不處于讀書窗內，應繼續按住指針鎖定桿，反復開啟和關閉電機，使指針處于讀數窗內。
