主要針對汽車空調各種漏點，整個系統快速100%不會誤報，10-30分鐘，100%找出各種泄漏點，代替加壓力，灑水，熒光粉，拆系統在水中浸泡的原始方法。
工作原理，主要針對氟的化學成份，稀濃度，抓捕分析，在空調系統中追捕氟的泄漏量，氟的顆粒量少0.01的分之一，100%分析。
原理Principle
利用一個高的真空泵，將空調系統可能微泄的氟利昂吸入探測器，探測器采用高頻磁場低壓電離的工作方式,吸入微量的氟利昂,其液晶顯示數字立刻上升，同時蜂鳴器報警。
by using a high vacuum pump, the micro leak freon can to inhale detector, detector adopts low-voltage high frequency magnetic field ionization ways of working, inhaled trace of freon, the liquid crystal display Numbers rise immediately, at the same time a buzzer alarm.
技術The core features
1)持續穩定的工作
2)能檢測0.01ppm的氟利昂,相當于0.05克/年的泄漏量。
1) stable and reliable work;
2) the highest accuracy to detect 0.01 PPM of freon, equivalent to 0.05 g/leakage of the year.
典型效果Tical effect
1） 蒸發器檢漏，在確定漏點前，無須拆風口，拆儀表盤；
2） 可以檢測到老化的空調軟管滲漏（肥皂泡、熒光劑測不到的漏點）；
3） 不制冷的汽車空調系統，不需要添加，即可檢測。
4） 看不到氣泡的氣門芯泄漏1秒鐘即可；
5） 半小時一輛車，檢測完畢，無須拆系統，無須水中浸泡；
1) the evaporator leakage, before determining leak point, do not need to diantle tuyere and tear open the dashboard;
2) can detect leakage of air conditioning hose aging (soap bubbles, fluorescent agent can't measuring leak point);
3) no refrigeration automobile air conditioning system, don't need to add freon, can detect.
4) 1 second can determined the leak valve core;
5) Half an hour to complete the detection of a car, no need to diantle the system, no water immersion;
使用介紹Method of use
蒸發箱，只要5分鐘，關閉空調，把探測器放在蒸發箱下面的風口，數字上升3-10左右，確定有漏。
the evaporation box: Five minutes is enough. Turn off the AC, and put the probe in tuyere on the bottom of the evaporation tank, figure up 3-10 or so, determine how leakage
在確定漏點前，無需拆風口before determined the leak point, with no need to open panel
壓縮機：只要5分鐘，探頭在機體，軸頭來回3-5次，數字上升5-15左右，確定有漏。
the compressor: Five minutes is enough.. Place the probe in the body and turn the head back and forth 3-5 times, and if the number rises by 5-15,then the leak is determined.
冷卻箱，10分鐘，把探頭隨著箱體結構來回均勻探測移動，數字上升，3-30左右，確定有漏。
the cooling tank: It takes about ten minutes. Move the probe with the body structure of the cooling tank at steady pace, and if the number rises by 3-30, then the leak is determined.
剩余管道的接頭處10分鐘把探頭隨管道走向來回3-5次，數字上升5-30左右，確定有漏。
the remaining of pipe joint: This step takes around ten minutes. Move the probe along the pipeline back and forth 3-5 times, and if the number rises by 5-50, then the leak is determined.
